Looking for:
Picture shows a Bondtech extruder, but you’ll get the idea? Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community. Register a new account. Sign in Already have an account? Sign In Now. Go to topic listing. Our picks New here? Get ahead with a free onboarding course SandervG posted a topic in Official news , February 9, Hi, Often getting started is the most difficult part of any process.
A good start sets you up for success and saves you time and energy that could be spent elsewhere. They’re ready for you on the Ultimaker Academy platform. I’d suggest an alternative method, which takes the compression of the filament by the hobbed wheel and thus the effective radius varies with spring tension into account, is as follows I don’t recall where I got it, so can’t attribute it :.
You need to be a member in order to leave a comment. Sign up for a new account in our community. It’s easy! Already have an account? Sign in here. SandervG posted a topic in Official news , February 9, Detailed Documentation of our hardware and software mods for reliable printing. Share More sharing options Followers 6. Prev 1 2 3 Next Page 1 of 3.
Recommended Posts. Jamezracer 10 Posted October 15, Link to post Share on other sites More sharing options Replies 53 Created 6 yr Last Reply 5 yr. Top Posters In This Topic 9 7 6 6. Posted Images. I agree that the Hobbed Wheel Upgrade it’s nice. Edited October 15, by Guest. The hobbed wheel listed is described on Amazon as designed for. Nice read, enjoyed the thorough technical explanation for each modification. Very interesting read, thanks for sharing.
BrayChristopher 36 Posted October 16, Jamezracer 10 Posted October 16, Is this a common problem with Ultimaker printers? Edited February 27, by esopalumpa tags. Link to post Share on other sites More sharing options Framar 26 Posted February 27, Hello, Never see that on our S5. Does it happen with any type of material? Stupid question but does the retainer clip on that locks the tube in place is in place? When mounting the bowden tube, do you push it far enough in, all the way down?
I disassembled and reassembled the feeder. Seems to be O. Which part is intended to absorb the bowden movement, esp. Edited March 2, by esopalumpa. It did it again… Is anybody able to shed any light on this? P3D 46 Posted March 4, Never had this happen at all On my UM2, the tube is also worn-out, but it keeps clamping well.
I think I installed it correctly. Therefore the question about where the rotation should be absorbed. I have checked already everything as you also did. Edited March 29, by guillermo. Thank you! JC40 2 Posted March 20, Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community.
Register a new account. Sign in Already have an account? Perhaps you should start over and explain at first what exact type of printer you’re talking about Do you have pictures? Also, those printer settings in Cura are part of the ‘Printer Settings’ plugin in the marketplace. If you do have an UM3, I would suggest you have little need for this plugin.
If you are still talking about the Bondtech DDG installation, it’s on the end of page 9 in the installation manual:. Just enter the value you want in the json file mentioned here in this thread. You just need to enable the developer mode to be able to ssh into the printer. The command for 3. Be sure to read the instructions very carefully and it should work. I am a noob and my problem was I was pressing “x” to save the json file when I was supposed to be pressing “:x” Always a good idea to go back in after you are done and verify that the values actually changed.
You need to be a member in order to leave a comment. Sign up for a new account in our community. Why Choose Print Your Mind? How to Use 3D Printers. Other Resources. Contact Us. General Inquiry. Request a Quote.
Insert the end of the material into feeder 1 and gently push it until the material is grabbed by the feeder and is visible in the bowden tube. Select confirm to. Do not change or adjust any parts of the Ultimaker products unless the change or adjustment is Ultimaker Connect, our free printer management solution. Learn how to set and adjust the tension of the feeder on your Ultimaker S5 or Ultimaker 3 3D printer. Colin will walk you through everything.
– Removing the filament
Apr 22, · This can happen when the feeder tension is set too high, but there’s also a chance that grinding can occur due to a problem in the hot end or Bowden tube, or a material issue. Follow this step-by-step guide in order to properly resolve any grinding issues that you may be experiencing with your Ultimaker and get back to the business of Estimated Reading Time: 1 min. Jan 29, · Ultimaker 3D printers ; Feeder tension Feeder tension. By JohnG, January 25, in Ultimaker 3D printers. Share To adjust the tension you should take your allen key and turn the screw there to position the pressure (it should be at the middle Register your Ultimaker for free 3D printer onboarding course. Oct 15, · Hi All, I have experienced grinding with ColorFabb NGEN Flex on my ultimate 2+ extended – I need to reduce the tension on my feeder – currently the feeder tensioner is set to the middle position, do I need to adjust this up or down to reduce the tension.
Sorry, the comment form is closed at this time.